Hoppa till innehåll
Free shipping on orders over 3000 SEK excl. VAT! Volume discount: 5 pcs 2% · 10 pcs 3% · 25 pcs 5%
Volume discount: 5 pcs 2% · 10 pcs 3% · 25 pcs 5%A Spot Check Shows Only One Moment: How to Document Core Temperature All the Way ThroughWhen a temperature measurement takes 0.4 seconds, it also gets done at every checkHow to know your thermometer reads correctly: check your own instruments against a reference with ±0.03 °C accuracyThe fridge never alarmed last night: how to detect temperature deviations before your goods are ruinedThe glare on the shiny surface hides the crack: how to see and measure the defect without guessingCarbon Dioxide Levels Reveal the Ventilation That Temperature Never ShowsWith 0.4-second readings, temperature checks become something you actually have time to doSee the fault behind the wall without having to take anything apart firstThe fault only showed up on Monday: how a humidity log reveals what happened over the weekendFind the fault in the electrical cabinet with a thermal camera before you put the current clamp on the cableVolume discount: 5 pcs 2% · 10 pcs 3% · 25 pcs 5%A Spot Check Shows Only One Moment: How to Document Core Temperature All the Way ThroughWhen a temperature measurement takes 0.4 seconds, it also gets done at every checkHow to know your thermometer reads correctly: check your own instruments against a reference with ±0.03 °C accuracyThe fridge never alarmed last night: how to detect temperature deviations before your goods are ruinedThe glare on the shiny surface hides the crack: how to see and measure the defect without guessingCarbon Dioxide Levels Reveal the Ventilation That Temperature Never ShowsWith 0.4-second readings, temperature checks become something you actually have time to doSee the fault behind the wall without having to take anything apart firstThe fault only showed up on Monday: how a humidity log reveals what happened over the weekendFind the fault in the electrical cabinet with a thermal camera before you put the current clamp on the cable

Extech PQ3350-1 3-Phase Harmonic Analyzer with Flexible Rogowski Clamps: When THD-F Exceeds 5% on a Factory 400 V Network, Causing Transformer Overheating, Capacitor Bank Deficiency, and 15% Higher Grid Fees

Published July 15, 2026 at 12:25

Electrical power quality was a theoretical physics concept until the 1980s. With the shift to switch-mode electronics in virtually all modern loads (from LED drivers to megawatt motor drives), harmonic currents have become a critical practical problem for industrial electricity suppliers and owners of large buildings.

The Extech PQ3350-1 is the complete 3-phase power and harmonic analyzer for this reality.

What are harmonic currents and why are they problematic

Traditional electrical loads (incandescent lamps, resistive heating, standard motors) draw CURRENT that is SINUSOIDAL — the same waveform as the grid voltage (50 Hz in the EU, 60 Hz in the USA). The current is in phase or nearly in phase with the voltage.

Modern switch-mode loads (LED drivers, DC chargers, inverters, VFD drives) draw current in SHORT PULSES — only during the brief moment when internal capacitors are charged. This non-sinusoidal current waveform can mathematically be DECOMPOSED via Fourier analysis into a sum of:

  • Fundamental (50 Hz) — the main component.
  • 3rd harmonic (150 Hz).
  • 5th harmonic (250 Hz).
  • 7th harmonic (350 Hz).
  • …up to the 25th-40th harmonic in practice.

Total Harmonic Distortion (THD) measures how much these harmonic components distort the waveform from a perfect sine wave:

THD = √(V₂² + V₃² + V₄² + …) / V₁

Where V₁ is the RMS of the fundamental and V₂, V₃, … are the RMS of the harmonic components.

The three problems caused by harmonics

1. Transformer overheating: Transformer core iron losses increase QUADRATICALLY with frequency (eddy currents) and LINEARLY with frequency (hysteresis). At harmonic frequencies (5×, 7× grid frequency), losses become 25-49 times higher than at the fundamental. A transformer sized for sinusoidal load experiences overheating at THD > 8-10 %.

Practical consequence: transformers with high THD loads have a shortened lifespan (15 years instead of 30-40 years) and can in extreme cases fail with a fire risk.

2. Compensation capacitor failure: Power factor correction (PFC) uses capacitor banks to compensate for reactive power from motor loads. Capacitor impedance is INVERSELY PROPORTIONAL to frequency (X = 1/(2πfC)). At harmonic frequencies, capacitor impedance is 5-10 times lower than at grid frequency.

This means that harmonic currents are CHANNELLED into the capacitors (as the lowest impedance path), causing:

  • Overheating and fire risk.
  • Capacitor swelling and leakage.
  • Resonance between the capacitor bank and network inductance.
  • Typical capacitor lifespan reduced from 15 years to 2-5 years.

3. Higher network fees: Electricity suppliers in Sweden (and the EU generally) began around 2015-2020 to penalize high THD via NETWORK FEE SURCHARGES. Standard models:

  • THD < 5 %: No extra fee.
  • THD 5-8 %: 5-15 % extra on the network fee.
  • THD > 8 %: 15-25 % extra + power to prohibit connection until correction.

For a factory with a 500 kW load, this can mean 50,000-150,000 SEK per year in extra costs.

Flexible Rogowski clamps — key differentiator

Standard current clamps use an IRON CORE (like a transformer). Advantages: high accuracy, low noise. Disadvantages: physically large, require access to an isolated cable, can only measure on CABLES (not busbars).

The Rogowski clamp (invented by Walter Rogowski in 1912) uses a flexible AIR-CORE loop instead of an iron core. Advantages:

  • Flexible shape: Can be wound around irregular shapes (busbars, collection rails, cable bundles).
  • No saturation: Can measure up to 10 kA without saturation.
  • Lightweight: A Rogowski clamp with 3000 A capacity weighs ~200 g. An equivalent iron-core clamp would weigh 3-5 kg.
  • Easy opening: The Rogowski clamp’s opening is easy to connect around a thick busbar.

Disadvantage: requires INTEGRATION electronics to correctly reconstruct the current waveform (the Rogowski clamp’s signal is proportional to the current DERIVATIVE, not the current itself). The PQ3350-1’s electronics handle this integration internally.

Measurement parameters (35 simultaneous on screen)

The PQ3350-1 measures and displays simultaneously:

  • Voltage: V_LL (line-line), V_LN (line-neutral), per phase + average.
  • Current: Per phase + neutral (calculated).
  • Power: Active (kW), reactive (kVAR), apparent (kVA), per phase + total.
  • Power factor: Cos φ per phase + average.
  • Frequency: Hz (typically 49.8-50.2 for the Swedish grid).
  • THD: Voltage THD and current THD per phase.
  • Individual harmonics: 1st to 25th harmonic per phase.
  • Waveform: 1024 samples/cycle display.
  • Phase imbalance: VUR (voltage unbalance ratio), CUR (current unbalance ratio), d0%, d2% (negative- and zero-sequence components).
  • Current through neutral: Calculated from 3-phase imbalance.
  • Maximum demand: Programmable period for electricity supplier billing comparison.

28 transient events

Grid voltage transients are short voltage deviations (microseconds to minutes) that cause:

  • Electronics faults (VFD tripping, LED driver fire).
  • Data corruption in digital systems.
  • Motor startup problems.

The PQ3350-1 can capture 28 such events with a programmable threshold:

  • DIP (voltage drop below X %).
  • SWELL (voltage rise above X %).
  • INTERRUPTION (complete outage).

Each event is time-stamped and the full waveform is stored for post-analysis.

Data Logging: up to 52,428 readings

Long-term monitoring is a requirement for power quality verification according to EN 50160:

  • Standard period: 7 days (168 hours).
  • Logging interval: typically 10 minutes or 15 minutes.
  • Calculated number of readings: 7×24×60/10 = 1008 points (10-minute interval).

The PQ3350-1’s 52,428-point memory covers:

  • 52,428 / 6 per hour = 8,738 hours = 364 days at a 10-minute interval.
  • This is sufficient for ONE YEAR of continuous monitoring — far beyond most practical needs.

EN 50160 power quality standard

The European standard EN 50160 defines acceptable power quality at the end consumer. Critical parameters and limits:

  • Voltage: 230 V ±10 % for 95 % of the time, ±10 %/-15 % for 100 % of the time.
  • Frequency: 50 Hz ±1 % for 99.5 % of the time.
  • Flicker: P_lt < 1 for 95 % of the week.
  • Harmonics: THD < 8 %, individual harmonics < 5 % (5th), 4 % (7th), 3 % (11th).
  • Phase imbalance: negative-sequence component < 2 % for 95 % of the week.

The PQ3350-1 measures all these parameters simultaneously. The logging period provides the basis for EN 50160 verification.

Optically isolated USB interface

Standard USB interfaces have a COMMON GROUND with the computer’s chassis. When measuring on a 400 V phase, this would create a risk of fault currents being led via the USB cable to the computer (damaging the computer and the operator).

Optical isolation: The USB signal is converted to an LED flash inside the instrument, transmitted via optical fibers to a detector on the USB output side. NO electrical connection between the measurement electronics and the USB interface.

Practical consequence: safe connection to a computer even when measuring on high-voltage grids. IEC 61010 standard met for measurement category CAT III / 600 V.

Applications

Industrial power audit: Verification of power quality in factories with high-power loads. Diagnosis of transformer overheating causes.

Data center installation: Verification of UPS output quality and network parameters for sensitive IT equipment.

Hospital power analysis: Verification of backup generator quality during power outages.

Wind and solar installation: Verification of inverter output and grid feed-in quality.

Compensation capacitor diagnosis: Identification of harmonic-caused capacitor degradation.

Metallurgy workshop: Arc welding, EDM machines, and induction heaters create dramatic THD.

Semiconductor manufacturing: Cleanroom power supply must have low EMI/THD for sensitive equipment.

Electricity supplier grid service: Verification of customer installation after complaints about voltage problems.

Consulting activities: Power quality consultants use it for customer installation audits.

Construction service: Verification of new installation power quality before handover.

Alternatives within the power quality measurement family

Extech PQ3450 (cheaper, ~35,000 SEK): 1200 A iron-core clamps, fewer parameters, less memory. Good for basic diagnosis.

Fluke 435 II Power Quality Analyzer (~150,000 SEK): More advanced, color screen, Class A (EN 61000-4-30). Calibration lab reference.

Chauvin Arnoux CA 8336 (~90,000 SEK): Mid-range step between PQ3350 and Fluke 435. Good for continuous industrial monitoring.

Dranetz PowerXplorer PX5 (~120,000 SEK): Standard in the USA for utility service.

PowerVar Sinergy 5 (~80,000 SEK): Fixed (permanent installation) power quality monitor.

Specifications

  • Model: Extech PQ3350-1.
  • Connection: 3-phase 3-wire or 4-wire.
  • Voltage: 40-600 V AC.
  • Current: via flexible Rogowski clamps, up to 3000 A.
  • Power: 0-9999 kW (dependent on CT/VT setting).
  • THD: measurement of fundamental + 1st-25th harmonics.
  • Waveform: 1024 samples/cycle display.
  • Transient capture: 28 events with programmable threshold.
  • Data logging: 52,428 single-phase or 17,476 3-phase readings.
  • Adjustable CT (1-600) and VT ratio (1-3000).
  • Optically isolated USB for safe PC connection.
  • Display: LCD with backlight, 35 parameters simultaneously.
  • Power supply: 8 AA batteries or AC adapter.
  • Class: CAT III / 600 V (IEC 61010).
  • Complete delivery includes: 3 flexible Rogowski clamps, 4 voltage leads with alligator clips, batteries, AC adapter, software, USB cable, case.

What you get for the money

Extech PQ3350-1 3-phase Power and Harmonic Analyzer with 3 flexible 3000 A Rogowski clamps, simultaneous measurement of 35+ parameters, THD analysis up to the 25th harmonic, waveform capture 1024 samples/cycle, 28 transient events with programmable threshold, 52,428-point data logging, optically isolated USB for safe PC connection, CAT III / 600 V safety, complete with clamps, voltage leads, batteries, software, and case. 62,920 SEK.

The standard tool for power quality consultants, industrial power audits, data center installations, hospital power services, wind and solar verification, compensation capacitor diagnosis, semiconductor manufacturing, and other applications where high THD, transients, phase imbalance, or harmonic-caused equipment degradation are part of the work. The premium over the basic PQ3450 is justified when measurements are continuous (multi-week logging) or when the flexibility of Rogowski clamps is critical for measuring on busbars and cable bundles.

Read more: Extech PQ3350-1 3-phase Harmonic Analyzer in the shop →

More news

All news