Published 12 July 2026 at 03:07
An injection molding manufacturer has a 5 kW heater that must maintain the plastic melt temperature at EXACTLY 180 °C. Temperatures that are too high degrade the plastic (discoloration, reduced mechanical strength); temperatures that are too low result in poor flow properties (mold filling defects). Tolerance band: ±0.5 °C around the setpoint of 180.0 °C.
With simple ON/OFF control (where the heater is either on or off), the temperature would fluctuate as follows:
- 170 °C: Heat turns on at 100 %.
- 180 °C: Heat turns off. However, the material has thermal inertia — the temperature continues to rise.
- 190 °C: Overshoot. The heat remains off.
- The temperature gradually drops below 180 °C. At 170 °C, the heat turns back on.
- Cycle after cycle: a 20 °C swing around the 180 °C target.
This 20 °C swing is completely unusable for precision production. This is where the PID controller comes in — a three-term control algorithm that allows the same system to stabilize at 180 °C ±0.5 °C.
PID: Proportional + Integral + Derivative
The PID controller calculates how much heat to apply based on three terms:
u(t) = K_p × e(t) + K_i × ∫e(τ)dτ + K_d × de/dt
Where:
- u(t) = output signal (e.g., 0-100 % heat output).
- e(t) = error = setpoint – current value (e.g., 180 – 172 = 8 °C).
- K_p = proportional coefficient.
- K_i = integral coefficient.
- K_d = derivative coefficient.
Each term responds to a specific aspect of the error:
Proportional term (P): Reacts to the CURRENT MAGNITUDE of the error. Large error → high heat. Small error → low heat. It is a simple principle but does not work alone — there is always a “residual error” that the P-term cannot eliminate.
Integral term (I): Sums ACCUMULATED ERRORS over time. If the system has been below the target for a while, the I-term accumulates — and provides extra heat to compensate. It solves the residual error problem from the P-term.
Derivative term (D): Reacts to HOW FAST the error is changing. If the temperature is rising quickly toward the target, the D-term reduces the heat earlier — to avoid overshoot. It acts as a “predictor”.
Combined: P provides fast reaction, I provides accuracy, and D provides stability.
Without the D-term: classic overshoots
If only P + I (PI control without D) is used, the following happens:
- At startup, the error is large (180 – 20 = 160 °C).
- The P-term provides 100 % heat.
- The temperature rises rapidly.
- At 175 °C, the error is still 5 °C — the heat is still high.
- At 180 °C, the error is 0 — but the heat is ON due to thermal inertia.
- The temperature continues to 195 °C = 15 °C overshoot.
- Now the error becomes negative. The I-term has accumulated a lot of integral error; it takes time to “reverse”.
- The system swings back to 165 °C, then up to 190 °C, with gradually damped oscillations.
The D-term prevents this by REDUCING the heat as soon as the temperature begins to RISE RAPIDLY. The system sees that “the next value will be higher than the current one” and compensates in advance.
PID tuning: the difficult part
Finding the right K_p, K_i, and K_d for a specific system is the difficult part. Well-tuned values provide stable, fast control. Incorrect values result in:
- K_p too high: Overreaction, constant oscillations.
- K_p too low: Slow reaction, never reaches the target value.
- K_i too high: Slow oscillations with a long period.
- K_i too low: Continuous offset from the target value.
- K_d too high: Sensitivity to measurement noise, jerky output.
- K_d too low: Overshoots during transients.
Classic tuning method (Ziegler-Nichols, 1942):
- Set K_i = 0, K_d = 0. Only P-control.
- Increase K_p until the system begins to oscillate with constant amplitude (Critical gain K_c).
- Note the oscillation period T_c.
- Use K_p = 0.6 × K_c, K_i = 1.2 × K_c/T_c, K_d = 0.075 × K_c × T_c.
This manual process requires 30-60 minutes for each new process. Today, it is done with AUTO-TUNING.
Extech 48VFL11’s auto-tuning
The 48VFL11 features “one-touch self-tuning” — the operator presses a button and the controller:
- Applies a STEP change to the setpoint (e.g., from 100 to 200 °C).
- Records how the system reacts over time — speed, overshoot, damping frequency.
- Calculates optimal PID parameters based on the recorded system behavior.
- Saves the parameters internally. It is now tuned for that specific system.
This procedure takes 5-15 minutes (depending on process inertia) — dramatically faster than manual Ziegler-Nichols. For industrial operation, auto-tuning is almost always sufficient.
The Fuzzy Logic addition
Classic PID is LINEAR — all three parameters are constant across the entire operating range. This is sub-optimal for different operating modes:
- With large error (startup, rapid change): an aggressive P-term is needed.
- With small error (steady-state): a soft P-term is needed for stability.
Fuzzy Logic is a technique for non-linear control. Instead of fixed parameters, “membership functions” are used which state “if the error is LARGE and rising RAPIDLY, apply an aggressive P-term”.
The 48VFL11’s “Fuzzy Logic PID” is a HYBRID: classic PID with fuzzy-rule-based adjustments of parameters based on the current operating state. Result: faster response during transients, better stability at steady-state.
The Soft Start function
When starting from cold (e.g., 20 °C) with a target value of 180 °C, the error is large (160 °C). The P-term provides 100 % heat. This causes:
- Thermal shock to the heating element (steep gradient).
- Mechanical stress on the workpiece material.
- Electrical peak load stress on the power grid.
Soft start limits the output signal to 30-50 % during the first 5-10 minutes, then gradually increases to 100 % when needed. This provides:
- Protection of element lifespan.
- Reduced mechanical stress.
- Avoidance of power grid peaks.
1/16 DIN — the panel mounting standard
The 48VFL11 is a 1/16 DIN form factor — 48 × 48 mm front panel. The DIN 43700 series defines standard panel mounting sizes for industrial instruments:
- 1/16 DIN: 48 × 48 mm.
- 1/8 DIN: 96 × 48 mm.
- 1/4 DIN: 96 × 96 mm.
- 1/2 DIN: 144 × 72 mm.
1/16 DIN is the standard for temperature controllers in industrial panel boxes. A cabinet can contain 20-50 such controllers for multi-zone control of complex processes.
Input types: thermocouple + RTD
The 48VFL11 accepts two sensor types:
- Thermocouple: Type K, J, T, E, N, R, S. Standard for most industrial applications.
- RTD (Resistance Temperature Detector): PT100, PT500, PT1000. Standard for high-precision and laboratory applications.
The difference:
- Thermocouple: robust, fast response, wide temperature range (-200 to +1370 °C for type K), but accuracy ±1-2 °C.
- RTD: slower response, narrower temperature range (-200 to +850 °C), but accuracy ±0.1-0.5 °C.
Output signals: relay + optional 4-20 mA
Standard: 1 relay output that switches the heating element ON or OFF. For resistive heating, this works well.
Optional: 4-20 mA analog output (48VFL13 model) which provides PROPORTIONAL control. For power electronics (SCR controllers, IGBT inverters) that accept a 4-20 mA signal.
Extra: 2 LATCHING alarm relays for high/low alarms, deviation alarms, band alarms. Critical for safety monitoring.
Applications
Injection molding and extrusion machines: Plastic melt temperature must be stable for product consistency.
Oven and sterilization equipment: Bakeries, laboratories, medical equipment.
Chemical process control: Reactor temperature, distillation columns.
Glass and ceramic production: Sintering furnaces, glass forming.
Food production: Pasteurization, chocolate tempering, dough fermentation.
Composite autoclaves: Autoclaves for aerospace and sports equipment manufacturing.
Soldering reflow and SMT soldering: Electronics production.
Heating of cooling water circuits: Industrial climate control.
What you get for the money
Extech 48VFL11 panel meter with Fuzzy Logic PID controller, 1/16 DIN (48×48 mm) form factor, dual 4-digit LED displays (process value + setpoint), tactile keypad, one-touch auto-tuning function, soft start mode for heating element protection, accepts thermocouple (K/J/T/E/N/R/S) and RTD (PT100/500/1000) input, 1 relay output (10 A/240 V AC for direct heating element operation), 2 LATCHING alarm relays with 8 alarm modes, panel mounting with snap-in clips. 4,158 SEK.
The standard instrument for medium-scale industrial temperature process control. The combination of Fuzzy Logic PID + auto-tuning + soft start eliminates the classic problem of “controllers are hard to tune” — the new operator can implement precision control within an hour of installation without understanding Ziegler-Nichols mathematics. For critical processes requiring ±0.5 °C precision, this type of PID controller is the standard choice, and the Extech model offers professional functionality at a fraction of OEM industrial prices.
Read more: Extech 48VFL11 PID controller in the shop →